StoneHarmonia Installation Guide
Installation Guide for Stone Harmonia Natural Thin Flexible Stone
Pre-Installation Requirements
Surface Preparation
• Ensure the surface is flat, solid, and free from dust and debris.
• Any loose particles or uneven areas should be addressed before installation.
Temperature Conditions
• The recommended installation temperature is above 50°F (10°C).
• If the stone slabs arrive rolled up, lay them flat for up to 48 hours to regain their natural shape.
• In cold conditions, a heat gun can be used to expedite flattening.
Required Tools & Materials
• Cutting: Use a circular saw or track saw with a 60-tooth carbide-tipped blade or a diamond blade with water cooling.
• Adhesive: Use qualified adhesives for standard applications and waterproof adhesives for wet or outdoor environments.
• Other tools: Measuring tape, pencil, pressure roller, masking tape, and metal trims (if needed).
Installation Steps
Unboxing & Preparation
• Remove the stone slabs from packaging.
• If they are rolled, allow them to lay flat.
• Slight flaking of the stone surface is normal duringunboxing and installation.
Measurement & Cutting
• Mark the required dimensions on the Natural Thin Flexible Stone.
• Cut precisely using a circular or track saw with a carbide-tipped blade, placing the slab face down. If using a diamond-tipped blade, it is not necessary to flip the slab.
Surface Cleaning & Masking
• Wipe down the installation surface to remove dust or debris.
• Use masking tape along the edges of the slabs to prevent adhesive overflow.
Adhesive Application
• Evenly apply the adhesive to the back of the stone or/and directly onto the surface, following the adhesive manufacturer’s instructions for each specific case.
• For translucent Natural Thin Flexible Stone, use a compatible adhesive that allows light transmission.
Placement & Bonding
• Position the stone slabs and press firmly against the surface.
• Use a pressure roller to ensure maximum adhesion and remove air pockets.
Grout & Finishing (Optional)
• If grout is used, leave a 1/16" to 1/8" gap for clean application.
• A silicone-based grout is recommended for flexibility and durability.
• Remove masking tape once grout is applied and cured.
Drying & Curing
• Allow the adhesive to cure for 24-48 hours, depending on temperature and humidity levels.
Completion
• Inspect the installation for alignment and finishing.
• Wipe the surface clean to remove any remaining dust or adhesive residue.
Surface Impregnation with Protective Hydrophobic Treatment Sealer.
• Apply the protective impregnation to a sample of the stone (there are treatments that enhance color and change the stone’s appearance, and others that do not, depending on the task). Allow it to dry and ensure the result meets your expectations.
• Apply the impregnation using a short-pile roller, spreading it evenly across the entire surface in one direction.
• Allow the impregnation to dry for 12-24 hours until fully dried.
• Apply a stone sealer every 18 months to maintain durability and warranty.
Metal Trim Options (Optional)
Metal trims enhance durability and aesthetics. Available trimtypes:
• U-Shape Trim
• T-Shape Trim
• L-Shape Trim
• Inside & Outside Corner Trims
Recommended Adhesives for Stone Harmonia Thinstone
Surface Type
Recommended Adhesive
Interior Walls
Loctite Power Grab All-Purpose Construction Adhesive, Gorilla Heavy Duty Construction Adhesive, BOSS 125 Multi-Seal, Liquid Nails Heavy Duty Construction Adhesive
Wet Areas & Exterior
Mapei Ultralite S2, Mapei Kerapoxy, K100 Hyperflex Litokol, X90 EpoxyLitokol, Laticrete 254 Platinum, Laticrete Latapoxy 300, Custom Building Products FlexBond Crack Prevention Mortar, Custom Building Products EBM-Lite Epoxy Bonding Mortar, Ardex X 77, Ardex WA Epoxy Adhesive
Translucent Installations
Mapeflex MS Crystal,
